Ø  Develop detailed MS and JSA for each task and activity. Ensure the Method Statement (MS) and Job Safety Analysis (JSA) comply with the relevant standards and regulations. Communicate the MS and JSA to the shutdown team and stakeholders.
Ø  Oversees the Work Permits / PTW (Permit to Work) process for all Construction activities.
Ø  Ensures that all Work Permits / PTW are issued by the relevant safety standards and regulations.
Ø  Coordinates with the Construction Managers and Supervisors to plan and schedule the Work Permits / PTW requirements.
Ø  Conduct pre-commissioning tests on extra low voltage substation / low voltage substation (ELVSS / LVSS) substation and panels. Verify the functionality and safety of ELVSS / LVSS equipment and systems
Ø  Perform commissioning activities according to approved procedures and standards. Document and report the results of commissioning tests and inspections.
Ø  Troubleshoot and resolve any issues or defects in the ELVSS / LVSS substation and panels.
Ø  Conduct the following tests on various Electrical Equipment:
Ø  Insulation resistance test: measure the resistance of the insulation material between the conductors and the ground.
Ø  Continuity test: check the electrical connections and circuits for any breaks or faults.
Ø  Earth loop impedance test: determine the impedance of the earth fault loop path and the prospective fault current.
Ø  Polarity test: verify the correct polarity of the live and neutral wires in a circuit.
Ø  RCD test: test the operation and performance of the residual current devices that protect against electric shocks.
Ø  Conduct a thorough review of the Piping and Instrumentation Drawing (P&ID) to ensure accuracy and compliance with standards and specifications.
Ø  Identify the process parameters and design conditions for the control valve and flow elements
Ø  Select the appropriate type and size of control valve and flow elements based on the process requirements and specifications.
Ø  Perform the required calculations to determine the flow coefficient, pressure drop, valve authority, and other relevant parameters for the control valve and flow elements
Ø  Verify the suitability and performance of the selected control valve and flow elements using simulation software or empirical methods.

Project: Crude Distillation Unit & Associated Down Stream Units Ruwais Refinery Expansion RRE Project, EPC- Package#1
RESPONSIBILITIES:
Ø  Check the accuracy and completeness of the Piping and Instrumentation Diagram (P&ID) against the design specifications and the Process Flow Diagram (PFD).
Ø  Verify the consistency and clarity of the symbols, labels, tags, and annotations used in the P&ID.
Ø  Identify and resolve any discrepancies, errors, or omissions in the P&ID.
Ø  Ensure the P&ID complies with the relevant codes, standards, and regulations in the field.
Ø  Evaluate the design and functionality of the control room layout and panel drawings and specifications. Identify the strengths and weaknesses of the current layout and arrange.
Ø  Check the accuracy and completeness of the instrument power distribution and network drawings
Ø  Verify the conformity of the drawings with the project specifications and standards
Ø  Identify and report any discrepancies, errors, or omissions in the drawings
Ø  Review the cable routings/schedule and termination drawings for accuracy and completeness. Identify any discrepancies or issues with the cable design and installation. Verify that the cable terminations are done according to the specifications and standards.
Monitoring and coordinating the site E&I activities of the contractor, vendor, and its sub-contractors for all electrical, and control instrument installations.
Ø  Monitor site material handling and preservation to facilitate construction progress and quality of materials.
Ø  Supervise the installation of various instruments pressure, temperature, flow and level sensors, control valves, actuators, PLCs, SCADA, DCS, and HMI. according to specifications and standards
Ø  Ensure the quality and safety of instrumentation works and report any issues or deviations
Ø  Coordinate with other teams and stakeholders to facilitate the completion of instrumentation works on time and within budget.
Ø  Resolve any issues or queries related to the technical specifications, quality standards, or delivery terms of the PO or quotations.
Ø  Ensure construction and pre-commissioning works are carried out according to company rules, regulations standards, and permit-to-work procedures as applied
Ø  Evaluate the Loop diagram, Logic diagram, and Process Hook-up, and verify the installation, calibration, and testing of instruments and devices.
Ø   Identify the tasks and activities involved in the shutdown process.
Ø  Preparation of instrument data sheets involving transmitter, control valve, pressure and level gauge, orifice plate, pressure, and flow switch.
Inspection of overall instruments, Loop Checking, Function test, Pre-commissioning, and Protection test of Equipments. 

RESPONSIBILITIES:
Ø  Coordinated with other teams and contractors to facilitate smooth and timely completion of instrumentation works
Ø  Supervised the design and implementation of CMS (Consumer Monitor System) for SSGC (Sui Southern Gas Company).
Ø  CMS also integrates with SSGC's existing systems such as SCADA (Supervisory Control and Data Acquisition) and GIS (Geographic Information System).
Ø  Identify the technical teams that will be responsible for installing the devices in different locations for gas distribution
Ø  Schedule training sessions with experienced instructors who can demonstrate and explain the installation steps and best practices
Ø  Monitor and evaluate the performance of the technical teams during and after the training sessions
Ø  Consider the ergonomics, safety, usability, and efficiency of the control room operators
Ø  Documented all the steps, inputs, outputs, and resources for each task and process
Ø  To train the staff for their role and responsibility of the stakeholders for each task and process
Ø  Establish the quality standards, safety measures, and performance indicators for each task and process
Ø  Review and validate the Standard Operating Procedures (SOPs) with the relevant experts and authorities.
Ø  Overseeing the instrumentation works and ensuring compliance with safety standards and specifications
Ø  Install and configure Closed-Circuit Television (CCTV) cameras and Biometric Systems for domestic and commercial purposes.  
Ø  Install and configure vehicle tracking devices in cars, bowsers, and trucks.
Ø  Monitor and troubleshoot all vehicle tracking, Biometrics, and Home security devices 24/7.
Ø  Provide feedback and support to the technical teams and address any issues or challenges they may face during the installation process
Ø  Explain the main features and functions of the software, and demonstrate how to use the software in different scenarios and tasks.
Ø  Provide hands-on practice and feedback for the end user. Review the software documentation and troubleshooting tips.
Ø  Promotes safety and awareness and safe performance among project team members, including consultants and contract personnel. 
 

RESPONSIBILITIES: (Control/Safety / F &G/ Telemetry System Commissioning and Technical Support)
Ø  Managed all control systems at the Naimat Basal Facility site, including DCS, ESD, F&G, SCADA, Metering System, Gas Turbine Controls, and multiple PLCs, Provided technical support, maintenance, and engineering projects implementation at the Naimat Basal oil and gas plant. Managed critical activities such as new wells/process train integration and new control systems integration with the current systems
Ø  Developed and implemented standard operating procedures for control system maintenance and troubleshooting.
Ø  Troubleshot and resolved any issues related to well-head controls during the commissioning and startup phases
Ø  Followed safety protocols and standards while working on well-head controls
Ø  Ensured compliance with safety and quality standards
Ø  Evaluated various options for control system integration based on engineering and safety criteria.
Ø  Identified and resolved issues with Engineering, Procurement, and Construction (EPC) contractors, Ensured design compatibility and compliance with existing LNG trains.
Ø  Conducted dynamic studies for steam and power systems. Worked with ABB DCS and SIS to monitor and control plant operations
Ø  Performed calibration and maintenance of Gas Chromatograph and Metering system
Ø  Configured and troubleshot SCADA systems and other instrument-controlled devices.
Ø  Compare devices the advantages and disadvantages of different control system proposals in terms of compatibility and reliability.
Ø  Assessed the feasibility and risks of integrating new control systems into existing ones from an engineering and safety perspective.